Plumbing 101: A Necessity for Bathtub Installation
Plumbing 101: A Necessity for Bathtub Installation
Blog Article
What're your beliefs on How to Install a Bathtub Yourself?
Mounting a tub isn't specifically brain surgery, yet it does require solid plumbing, woodworking, and in some cases, tiling abilities. Replacing an old bath tub with a new one is likewise a reasonably tough project. If the old tub is readily easily accessible, the project can move rapidly; if you need to open up a wall to eliminate the old bathtub and also position the brand-new tub, the job is a lot harder. In either situation, the task is within a home handyman's skills, although you will certainly require an assistant to leave the old bathtub as well as embeded in the new one. Make sure you have actually qualified on your own for the work and fit attempting it. Rather than working with a contractor to take over a halfway-completed project, it is better to think about utilizing one prior to you begin. Opportunities are you might require a specialist plumber to make tube links.
This short article will certainly assist you mount a brand-new bathtub in your shower room if you have actually already gotten a new bathtub and don't need to alter the setup of your previous water pipelines.
Your tools and also product checklist should make up the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your setup, after that the first thing you must do is separate the supply of water. After doing so, turn on the faucets to drain any type of water remaining in the system. The procedure of removing the existing faucets can be rather problematic as a result of the restricted accessibility that is commonly the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the taps. Have a towel all set for the remaining water that will certainly originate from the pipes. When the supply pipes have been removed, make use of the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from turning during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old sealing compound.
Before going on to fit the new taps, contrast the pipe links on the old taps to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly require a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and also the other end offers a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin ensuring that the washing machines are in place in between the faucet and the sink. Secure the tap in place with the maker provided backnut. Once the tap is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The former type ought to be linked to the tap ends first, tightening up only by hand. The supply pipes can later be connected to the various other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Tub
Utilizing the two wooden boards under its feet, put the tub in the needed position. The wood boards are useful in evenly spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto 4 little points.
The following objective is to make certain that the tub is leveled all round. This can be achieved by inspecting the level as well as changing the feet on the bathtub until the spirit level reviews degree.
To mount faucets, fit all-time low of the outermost flexible tap adapter to the ideal supply pipe by making a compression join; after that do the exact same for the other faucet.
Turn on the water supply and also examine all joints and also brand-new pipework for leaks and tighten them if needed. Fill the bathtub and additionally check the overflow electrical outlet and also the normal outlet for leakages.
Finally, deal with the bath paneling as described in the producer's instruction manual. Tiling and sealing around the bath tub should wait till the bath tub has been made use of a minimum of when as this will certainly resolve it right into its final setting.
Getting ready for the Setup
To start with, the sustaining frame provided with the bath ought to be fitted (if required) according to the producer's directions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is important to ensure that if the faucet includes a plastic washer, it is fitted in between the bath and the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to prevent stress on the tub.
Fit the versatile faucet connectors to the bottom of both taps using 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you utilize all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom should currently prepare to be fitted in its last position.
Tiling Around the Tub
In the location where the bath meets the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to split a rigid seal, triggering the water to pass through the wall surface in between the bath as well as the tiling, causing issues with moisture and also feasible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your fixtures as well as installations. They are offered in tubes and cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of drenched paper or soft rope. Remember to always fill the bath tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealer can split fairly very early if you do not think about this motion before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently available on the marketplace. It is advisable to fit the floor tiles using waterproof or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like reading about How to Install a Bathtub Yourself? Give a comment down the page. We will be interested to know your views about this review. We hope to see you back again soon. Liked our article? Please share it. Help somebody else check it out. Bless you for your time. Kindly come by our blog back soon.
Tailored emergency solutions; call now. Report this page